There are common misconceptions about alternatives to chlorinated pools. Many water pool, in turn, the belief that it is more economical and less maintenance rooms. These assumptions are completely wrong. If hypochlorite pool you want, you can make money, a lot of headaches and a lot of time to save only with the help of bleach. Bleach is typically 6% sodium hypochlorite.
A swimming pool with sea water is a swimming pool instead of chlorine calcium hypochloriteHypochlorite pool. The difference is that to do the same chlorine. Technically, a Salt Water Chlorinator chlorine gas by electrolysis of the salt works by releasing water of the pool. Two to 500 pounds of salt in the pool water was added to reach a saturation of about 3200 parts per million. The salt water is then transmitted when a cell chlorine plant that is loaded electronically, this process uses chlorine gas and salt. The chlorine gas thencombines with the pool water to create liquid chlorine bleach.
If you are considering such a salt water chlorinators are, there are some things you should consider before buying. Many shops and swimming pool builders tend only to professionals of these units. You should know what problems arise frequently in the rule and the reason for them to help you avoid unnecessary disappointment with this new investment.
This list will help you to recognize somethe most common problems with products for water treatment:
1 Many complain about the inability to achieve the desired chlorine content. This can be done from the pool pump / filter is not long enough for the unit should be created to provide the necessary amount of chlorine. Factors that increase the demand for chlorine is difficult to invite swimming, sun, heat, low stabilizer.
2 Ifthe salt content is too low, then the device is not enough chlorine.
3 If the stabilizer (cyanuric acid) is too low, the chlorine will not long stay in the bath water, and the device may not be able to keep up with demand. This is very common. Many problems occur when the stabilizer (cyanuric acid) are too low. 80 ppm is recommended by most manufacturers. In humid climates, can be up to 120 ppmnecessary to keep the chlorine in the pool. If the stabilizer is too low, the chlorine is produced will be burned by the sun. Air conditioner acts as a sunscreen for your chlorine. You can use the inner surface of the pool with a high damage cyanuric acid. High concentrations of stabilizer also cause the skin to itch.
4 If the salinity is too high, the cell might otherwise result in an incorrect reading of salt. The cellmay indicate salt. If this is done without checking the true reading, you can more than salt water. Most systems do not work if the salinity is too high or too low.
5 If phosphates in water (stain removal products on the market are loaded with phosphates), are food for algae. Some may not agree on these products and say they have no effect. We have seen this on aregularly and have the water test, to say the opposite. If the phosphate is too high, the salt water Chlorinator act as if it does not create chlorine. If chlorine, chlorine, immediately creates in the fight against algae is growing, even if not visible. If this happens, the pool is not possible to reach and build a reserve of chlorine in the water. (1-3 ppm)
No need to first common myth of pH with salt water concernsChlorine plant.
The truth - if the pH and alkalinity out of balance, the chlorine less effective. The pH should be 7.4 to 7.6. With a saltwater chlorination Chlorinator is similar to using liquid chlorine both have a high pH (11.7) chlorination. A common problem is that home and apartment owners do not tend to combine their pH and alkalinity sufficient evidence. The main reason is that too many manufacturers and dealers to sell these systems as "set and forget" solution. Most people withSalt systems are running their pH 7.8 to 8.0. This is bad for two reasons. One of the pool is in Range mode and two chlorine surrounded by higher alkalinity pH. And 'better between 7.4 to 7.6 when using chlorine.
Myth # 2 common pools are salt water pool surfaces and equipment safe.
The truth - The same salt is the attack on concrete questions and plaster materials bridge. This is a relatively slow process, because the salt is low. The saltcan also kill any landscape in or around the pool and the water level in the field.
If the sodium is too high, the main problem of corrosion by the chlorine produced by the electrolytic cell. Chlorine bleach can reagents can give a "false negative" and the damage to people grossly over chlorine your pool equipment, water surface, lights and stairs. A common problem is corrosion on the scale. The bridge anchorare typically cast and the conductor is usually made of stainless steel. The salt water will corrode the overtime anchor.
Everyone should be aware that if you salt water (in 2800 ppm or higher range) you should be ready to seal your own, especially if it is porous as limestone. Otherwise, the salt is dry and begin to affect your business. In addition to sealing the stone, and caution is also advisable to address the more cumshots at the end of each day to bathewith fresh water. Even if the pool of salt water is not at a level of 3000-3500 ppm corrosive if the water meets the management and evaporates, leaving a pure salt. The pure salt is corrosive and is probably due to corrosion of coping.
Some landlords refuse to build a swimming pool salt water pools with cream or taupe limestone coping. Every customer who wants to be confronted with a SWG pool, needs to make a rule to sign a release form. Pool builders have said thatmust replace a significant amount of these two types of coping strategies over the past year.
Myth # 3 common size fits all
The truth - It 'very important when you buy one chlor, make sure that the equipment for your swimming pool. You're better off with a chlorine for the pool is too large than too small. A chlorine is too great to be back or run for less time each day to make the cells take longer. One unit is too small for my algae problems later if you do not runfor longer periods each day, or add additional chlorine (No, not salt) on a regular basis.
Myth 4 There is no common maintenance of a pool of salt water.
The truth - All cells Saltwater generator should be cleaned. This must be done before the calcification is within the cell body of a large block. If left too long, it will do two things.
1 Breaking the cell envelope.
2 Shorten the life of the cell.
It 'also very important to watch your saltLevel in the pool. A low-salt (less than 2000 ppm) results in oxygen production and damage to metals platinum anode, thus shortening the life of the cell. It is recommended that the salinity of the upper end of the scale, try to keep the manufacturer for the model. It 'important to ensure that exceed the maximum capacity of power as the rectifier and the transformer can be damaged.
As with any pool must maintain a correct pH. AlsoCyanuric acid levels should be maintained or quickly dissipate chlorine from the pool. To repeat once again, salt water pools are not chlorine-free swimming pools. For those who really do not have a swimming pool chlorine, copper-ionization is a good choice.
|
Price : $139.99